Menu

浦东江西钢化车库地坪多少钱一平方 除漆一般能够分为两种状况,一是将部分破损的涂膜去除,对无缺的涂漠进行保存,这主要是针对于小面积破损的地坪而言。另一种状况是将将整个地坪外表的涂装悉数去除,直到显露基材。水性环氧自流平地坪施工工艺:①素地处理: 依素地状况做好打磨,修补,除尘;以强力打磨机铲除地坪外表杂质,打扫地坪的杰出物,惠发并刮除地坪外表之浮浆粉尘,测定地坪水分含量。旧地上破损,裂缝处用环氧中涂加高倍石英砂补科技平地上凹坑。②水性环氧底漆:只需不积水或不明显渗漏就可施工,具有必定透水气功用,能增强素地强度及添加涂层封素地的附着力;外表整理洁净后,运用滚筒涂布环氧树脂底涂一道。③水性环氧中涂:将水性环氧树脂参加适量石英砂,用镘刀将其均匀涂布一道,用于添加厚度及涂层抗压强度;运用环氧树脂填加石英砂,全体批涂一道。④水性环氧批土:依实际需要施工二至三道,要求到达平坦无孔洞,无批刀印及砂磨印为准;⑤水性环氧面漆:用滚涂型水性环氧面漆二道,或镘面型水性环氧面漆一道,完工后要求全体地上光泽柔软,洁净,色彩均一,无空鼓;运用锯齿镘刀将环氧树脂自流平面涂资料段进成铺设一道。⑥施工完结: 36小时后方可上人,96小时后方可重压。(25℃为准,低温敞开时间需适度延伸) 水性环氧自流平地坪施工注意事项:1,施工地坪不得有水气,油渍,若地上场所不具电话备条件,两边要洽谈处理。2,楼板混凝土强度需到达3000psi。3,平坦度及泻水斜度要求由甲方土建单位完结后***交乙方施作。4,夜间施工若采光缺乏区域甲方供给足够照明。5,工地足够的水电供应。6,施工区域不得穿插施工并由甲方派人控制。7,环氧树脂面涂完工后,甲方应派人员控制48小时,才可敞开运用。 当涂装过地坪涂料的外表呈现了起皮,起泡,腐蚀,开裂等现象时,咱们需要将这部分有质量问题地坪涂装彻底去除去,只需露前涂装前的基材才可进行从头涂装。在进行涂装前要先弄清楚原地坪涂料的涂装系统,以便挑选到适宜的地坪涂料。假如前次涂装的地坪底漆是环氧类或聚氨酯涂料,上面能够配套涂装的涂料规模则挑选面较宽,大部分的涂料都能够在上面直接涂装。假如底漆选用的是单组份丙烯酸或其它类的易挥发的涂料,假如随意的挑选地坪涂料涂装,很简单呈现咬底的状况,在进行涂装时必定要慎重挑选涂料。 四种常用的除漆办法: 一,机械除漆法机械除漆指借助于必定的施工东西来进行除漆作业,如手艺打磨,动力东西,抛丸,高压力(磨料)射流等办法,都是能够有用的去除旧地坪油漆层的办法。 二,火焰除漆法火焰除漆是指经过火焰加温的办法使旧漆层焦软,起泡,在此一起用刮刀进行刮铲旧地坪漆膜。三,碱液除漆法In addition to paint can generally be divided into two cases, one is the partial damage of the film to remove, to preserve the integrity of the desert, which is mainly aimed at the small area of damaged floor. The other is to remove the entire surface of the entire floor coating until the exposed substrate. Construction technology of waterborne epoxy self leveling floor:1. Ground treatment: according to grain to good condition burnish, repair, dust; with strong grinding machine to remove impurities on the surfaces of floor, floor sweeping prominence, benefits the and scraping floor surface laitance dust removal, the determination of floor moisture content. The old ground damage and crack with epoxy coated quartz sand filling technology heightening ground surface pits.II waterborne epoxy primer: as long as no water or not obvious leakage can be construction, with certain water vapour permeability function, can enhance the ground strength and increased coating sealing adhesion; clean the surface using roller coated with epoxy floor paint.The waterborne epoxy coating, waterborne epoxy resin is added in the appropriate amount of quartz sand, with steamed bread knife will be evenly coated, for increasing the thickness and coating compressive strength; use epoxy resin filled with quartz sand, the overall number of coated one.The waterborne epoxy group of soil: according to the actual needs of the construction of two to three, to achieve smooth no holes, no batch printing and knife sand grinding printed quasi;The waterborne epoxy topcoat: rolling type coating of waterborne epoxy finish second, or trowel facial waterborne epoxy topcoat. After the completion of requirements overall surface luster and soft, clean, uniform color, no hollowing; use toothed trowel epoxy self leveling coating material of impact of laying a road.The construction is completed: 36 hours before people, 96 hours behind the weight. (25 degrees C), the low temperature open time to be moderately extendedMatters needing attention in construction of waterborne epoxy self leveling floor:1, the construction floor shall not have moisture, grease, if the site is not phone preparation, both sides should negotiate.2, the strength of the concrete floor to reach 3000psi.3, the flatness and water drainage slope required by the completion of the civil engineering unit *** to Party B.4, at night, if the lighting is insufficient to provide adequate lighting area.5, the site adequate water and electricity supply.6, the construction area shall not cross the construction and by Party A to send someone to control.7, epoxy resin surface coating is completed, Party A should send personnel to control for 48 hours before it can be opened to use.When painting floor coating the surface of the skin, bubble, corrosion and cracking phenomenon, we need to this part of a quality problem of floor coating completely removed, as dew before coating the substrate to re painting. Before painting, we must first clear the coating system, so as to select the appropriate floor paint. If the last coating of floor primer is epoxy or polyurethane paint, the paint can be coated with a wider range of choice, most of the paint can be directly coated on the above. If the primer is one component acrylic acid and other volatile paint, if the random selection of floor coating, easy to bite the end of, in painting must careful selection of coatings.Four common methods of removing paint:Mechanical paint removing methodMechanical removal of paint to aid in certain construction tools to remove paint, such as hand polished, power tools, shot blasting, high pressure abrasive jet etc. method, can effectively remove old floor paint layer.Two, flame paint removal methodFlame removing paint is a method that makes the old paint layer coke soft and foaming by flame heating.Three, alkali paint removal method